How to fix packet loss
If the test found packet loss above 1%, first find where it happens. Run the packet loss test on Wi-Fi, then on a cable plugged into your router, then on a cable plugged straight into the modem. Loss that goes away on a cable is a Wi-Fi problem you can fix at home. Loss that stays on a cable at the modem is usually your provider's to fix, and your test results are what they'll ask for.
How much is a problem
Our test sends a burst of small UDP messages, the kind games and calls use, and counts how many come back. On a cable, 0% is normal. The verdict's limits are 1% or less for competitive games, 2% or less for video calls and 5% or less for 4K streaming. A single run that shows 1% once can be chance; loss that shows up run after run is worth chasing. See how much packet loss is acceptable for the full ranges.
Step 1: find where it happens
Use one computer for every run so the device stays the same. Run the packet loss test three times at each step and note the results.
- On Wi-Fi, where you normally use the computer.
- On a cable into the router. If loss drops to 0%, the problem is Wi-Fi: skip to step 3, Wi-Fi interference, below.
- On a cable straight into the modem, with the router unplugged from it. (If your modem and router are one box, skip this step.) Nintendo's latency troubleshooting suggests the same check: connecting directly to the modem shows whether your router or cable is the cause.
How to read it:
| Wi-Fi | Cable at router | Cable at modem | Where the loss is |
|---|---|---|---|
| Loss | None | None | Your Wi-Fi |
| Loss | Loss | None | Your router or the cable to it |
| Loss | Loss | Loss | The modem, the line or your provider |
If you can't plug a computer in at all, test a phone right next to the router, then far from it. Loss that grows with distance points to Wi-Fi.
Also check the time. Loss only in the evening, on every device and on a cable, points to congestion on your provider's network. Run the test again at a quiet hour, such as mid-morning, and compare.
Step 2: cables and connectors
A damaged cable or a loose plug can drop packets while still showing a link.
- Swap the Ethernet cable between the computer and the router for another one. Nintendo's troubleshooting suggests trying a different Ethernet cable for the same reason.
- Unplug and firmly re-seat every cable on the path: computer, router, modem and, on cable internet, the coax into the modem.
- Look for kinked, crushed or chewed cables and bent connectors. Replace anything that looks damaged.
- Restart the modem and router: unplug both, wait 30 seconds, plug the modem in first, then the router.
Test again on a cable after each change.
Step 3: Wi-Fi interference
If the loss only happens on Wi-Fi, the signal is being drowned out or is too weak. Apple's wireless interference guide lists the usual causes and fixes:
- Move closer to the router, or the router closer to where you use the internet.
- Keep the router away from microwave ovens, cordless phones, wireless cameras, fluorescent lights and power cables.
- Use the 5 GHz band where you can. Bluetooth and 2.4 GHz Wi-Fi share the same band, so it's more crowded.
- Let the router choose the least crowded channel, or change it by hand.
- Remove obstructions: metal is the worst, and concrete and plaster also weaken the signal.
High ping and jitter on Wi-Fi covers bands, placement and mesh systems in more detail.
Step 4: the modem's signal readings
On cable internet, a weak or noisy signal on the coax line is a common cause of loss at the modem. If your modem's web page shows signal readings (downstream power, signal-to-noise ratio, upstream power), take a screenshot while the loss is happening.
We don't give target numbers here. We couldn't find a major cable provider that publishes its acceptable ranges in its own support pages, and the forum figures that circulate vary. Your provider can read the values from its side and tell you whether they're in range.
On 5G home internet and Starlink, the readings are in the provider's app instead: see the T-Mobile and Starlink guides. Starlink's app shows a "Recent interruptions" alert when its dish has seen elevated packet loss in the last 15 minutes, which Starlink says can come from extreme weather, a temporary network issue or obstructions.
Step 5: when to call your provider
Call when the loss shows up on a cable plugged straight into the modem (or into your provider's combined box), across several runs, and after you've swapped the cable and restarted everything. Before you call:
- Run the packet loss test on a cable at least three times, at different times of day if you can.
- Copy each result (the Copy result button gives plain text) and note the date and time.
- Screenshot the modem's signal page, if it has one.
Then tell them, in this order:
- "I'm losing X% of packets on a wired connection directly to the modem."
- "It happens at these times," with your dated results.
- "I've replaced the Ethernet cable, re-seated the connections and restarted the modem and router."
That's usually enough to skip the "restart your router" script and get a line check or a technician. Starlink, for example, asks for screenshots of the tests and the date and time they were run when you open a ticket.
Test again
After each fix, run the packet loss test on the same device and connection you used before. Aim for 0% on a cable and 1% or less on Wi-Fi.
Sources
Checked November 2026.