Starlink latency and bufferbloat

Starlink's stated goal is a steady 20 ms median latency, and it reported a 33 ms median in the US at peak hours in 2024. If your ping is far above that, or it spikes when the line is busy, check the Starlink app for obstruction alerts first, then test at off-peak hours. If you use your own router behind Starlink, turn on its smart queue management (SQM) to control bufferbloat.

In its paper Improving Starlink's Latency, Starlink sets a goal of a stable 20 ms median latency with minimal packet loss. It reported that US median latency at peak hours (6 to 9 pm local time) fell from 48.5 ms to 33 ms, and worst-case peak latency from over 150 ms to under 65 ms. It names four causes of latency: the distance to the satellite and back, the ground route from its gateways to the internet, scheduling on the shared radio link, and processing delays and buffers that were too large, which it says it has resized to reduce bufferbloat.

It also says it added active queue management (fq_codel) to the Starlink Wi-Fi router, so one person's big download shouldn't affect another person's game. That's the same idea as the bufferbloat fix for other connections.

Starlink also notes that speeds can be lower or uneven during peak hours, 6 pm to 11 pm local time, when many users are online.

Our ping is an HTTP round trip to the nearest Cloudflare location, so it won't match the Starlink app's figures exactly. Compare our results with each other, at different times, rather than with the app.

Step 1: Check for obstructions

Starlink switches between satellites many times a minute and learns where trees and buildings block its view. Brief switches usually go unnoticed. But Starlink says an obstruction that stays in the dish's view can cause intermittent outages, dropped packets and lower speeds: exactly the spikes and loss our test picks up.

In the Starlink app:

If the app says Obstructed and interruptions keep happening, Starlink's fix-obstructions steps are: move the dish to a clear spot (unplug and reboot it when you move it), cut back the branch, or raise the dish above the obstruction with a mount. Its install guide says the dish needs a clear view of the sky from about 20° above the horizon, all the way around. Check too for leaves, soil or snow on the dish. If you can't do it safely, Starlink says to get professional help.

Step 2: Test at different times

Run the ping test or the bufferbloat test once in the evening and once mid-morning, on the same device. If results are fine off-peak and poor between 6 and 11 pm, that's network congestion, which no setting at home fixes. If they're poor at all hours, look at obstructions and Wi-Fi first.

Starlink's own slow-speed checks are worth doing before you change anything: turn off any VPN, test on the 5 GHz band close to the router, and use Cat5e or better Ethernet cable (Slow speeds: troubleshooting).

Step 3: Using your own router: bypass mode

If you want your own router's features, such as SQM or a mesh system, Starlink lets you connect it. Its bypass mode page explains how by hardware:

  • Router Mini: Starlink app > Settings > Bypass Mode > Enable. A violet light shows it's in bypass mode.
  • Router 3: enable bypass mode in the Starlink app, then plug your router into one of the Ethernet ports on the back of the Starlink router.
  • Starlink Performance (Gen 1, Gen 2 and Gen 3): no bypass needed; plug your router into the power supply.
  • Gen 1 router: replace it with your router.

Two cautions from Starlink: the app can't turn bypass mode off, so getting out of it takes a factory reset of the Starlink router; and Starlink doesn't guarantee performance or compatibility with third-party equipment, and its troubleshooting for it is limited. To get accurate speed results with your own router, Starlink suggests connecting a computer by Ethernet directly to the Starlink power supply, or bypassing your own router.

Step 4: Turn on SQM on your router

With your own router in charge, turn on its smart queue management, using the steps for OpenWrt, eero, UniFi or ASUS. Where it asks for speeds, measure first with SQM off, then start just below your measured download and upload.

Starlink's speed changes through the day, which makes a fixed limit a compromise: set for the evening and you waste speed in the morning; set for the morning and bufferbloat returns in the evening. Set it from an evening test if games and calls in the evening matter most. bufferbloat.net points to cake-autorate, which adjusts the limit as the line's speed changes, for links like Starlink, LTE and cable.

If you'd rather not run your own router, the Starlink router's own fq_codel queue management is already on.

Test again

Run the bufferbloat test in the evening, on a cable to your router if you can. Grade A or B means a busy line won't hurt games or calls. If the grade is fine but ping jumps every so often, bufferbloat isn't the cause; go back to the obstruction map and the app's alerts, since Starlink links obstructions to intermittent outages and dropped packets.

Sources

Checked November 2026.