High ping and jitter on Wi-Fi
If your jitter is above 10 ms, or your ping is much higher on Wi-Fi than on a cable, the Wi-Fi link is adding the delay. The biggest fix is a cable for the gaming PC, console or work computer. Where a cable isn't possible, use the 5 GHz or 6 GHz band, bring the device and router closer with fewer walls between them, and let the router pick a clear channel.
Why Wi-Fi adds ping and jitter
Our test's ping is an HTTP round trip to the nearest Cloudflare location, and jitter is the average change between one ping and the next. On a cable, both are usually steady. Wi-Fi is a shared radio channel: your devices, your neighbors' networks, Bluetooth gear and even a microwave oven take turns on the air, and a weak signal means packets have to be sent again. Each wait or retry adds a few milliseconds to some packets and not others. That's jitter.
The verdict's limits are jitter of 10 ms or less for competitive games and 30 ms or less for video calls. If you're not sure Wi-Fi is the cause, run the Wi-Fi against Ethernet comparison first: it takes about ten minutes and tells you for certain.
Step 1: Use a cable where it matters
A cable takes the radio out of the path. T-Mobile's support pages say a LAN/Ethernet connection typically provides the fastest speeds, and Nintendo's latency troubleshooting starts with using a wired connection if possible.
Wire the devices that need low ping (a gaming PC, a console, the computer you take calls on) and leave phones and tablets on Wi-Fi. If the router is in another room, a long flat Ethernet cable along the baseboard often works.
Step 2: Use 5 GHz or 6 GHz, not 2.4 GHz
Most routers broadcast more than one band:
- 2.4 GHz reaches farthest but is the slowest, per T-Mobile's network speed page. It's also the busiest: Apple notes that Bluetooth and 2.4 GHz Wi-Fi share the same band.
- 5 GHz is faster but reaches less far.
- 6 GHz is available on newer routers and devices. Apple's recommended router settings say to enable every band your router supports.
If the router uses one network name for all bands, it chooses the band for each device. If a device near the router keeps landing on 2.4 GHz, some routers let you split the bands into separate networks so you can choose. Starlink, for example, has a Split 2.4 / 5 GHz networks switch in its app, and T-Mobile's T-Life app can create separate 2.4 GHz and 5 GHz networks.
Apple also recommends a channel width of 20 MHz on 2.4 GHz and Auto on 5 GHz and 6 GHz. The narrow 2.4 GHz setting reduces interference, including from Bluetooth.
Step 3: Place the router and the device better
Distance and walls weaken the signal, and a weaker signal means more retries.
- T-Mobile's guidance for its gateway: devices about 15 feet away are great for gaming, 20 to 25 feet may see reduced speed for gaming and video calls, and 35 feet may see much lower speeds.
- eero suggests placing its units halfway between floor and ceiling, not on the ground, and away from brick, stone and metal walls.
- Apple says metal is the worst obstruction, with concrete and plaster close behind.
- Keep the router away from microwave ovens, cordless phones, baby monitors, fluorescent lights and power cables. Apple, eero and T-Mobile list these between them.
The easiest test: carry a laptop next to the router and run the jitter test. If jitter drops there, distance or walls are the problem.
Step 4: Pick a clear channel
In apartments, a dozen networks can share the same few channels. Apple recommends setting the router's channel to Auto, so it picks the best one, and using different channels on routers that sit near each other. Fewer devices on the same band also helps: Apple suggests reducing the number of devices competing for it.
Step 5: Mesh systems: wire the nodes if you can
A wireless mesh node relays your traffic to the main router over the air, so every packet makes two radio trips instead of one. That adds delay and jitter, especially when the node is far from the router.
- If your home has Ethernet runs, eero says wiring its units together is an option.
- If it doesn't, keep nodes within range of each other. eero suggests 20 to 30 feet apart, no more than 50.
- T-Mobile suggests putting a mesh unit in the open, at mid-height, near the center of the home.
- For the gaming device, connecting it to the main router (by cable or Wi-Fi) usually beats connecting it to a far node.
Step 6: Laptop power saving
Battery-saving modes are worth ruling out, but neither Microsoft nor Apple documents an effect on Wi-Fi latency, so we won't claim one. To check for yourself, run the jitter test once in your normal mode and once with saving turned off:
- Windows 11: Energy saver is a toggle in Quick Settings.
- Mac: Apple menu → System Settings → Battery, then under Energy Mode change Low Power Mode to Automatic (About Power Modes on your Mac).
If the second run is clearly steadier, leave saving off while you play or take calls.
Test again
Run the jitter test from the same spot as before. It runs about twice as long as the ping test, so its figure is steadier. Aim for jitter under 10 ms for games and under 30 ms for calls. If Wi-Fi still can't get there and a cable can, the cable is the fix.
Sources
Checked November 2026.
- Apple: Resolve Wi-Fi and Bluetooth issues caused by wireless interference, Recommended settings for Wi-Fi routers and access points, About Power Modes on your Mac
- Microsoft: Energy saver
- eero: Where should I place my eeros?
- T-Mobile: Network speeds, Troubleshooting
- Nintendo: Issues with latency while playing online
- Starlink: Slow speeds: troubleshooting